Storefront Door Repair
Aluminum and glass entrances: pivots, floor and overhead concealed closers, narrow-stile locks, and alignment.
View service →When an automatic door stops opening, opens too slowly, or closes on people, it's a safety problem and an accessibility problem. We repair low-energy ADA swing operators, push-plate actuators, sensors, and automatic sliding doors at Charlotte businesses.
| Systems | Low-energy swing operators, power-assist, automatic sliding doors |
|---|---|
| Actuators | Push plates, wave switches, motion and presence sensors |
| Standards | ANSI/BHMA A156.19 (low-energy), A156.10 (full power) |
| Safety | Daily owner safety check and annual certified inspection recommended |
| Where | Charlotte city limits only |

What we usually find when a Charlotte business calls about this, and what we do about it.
| Symptom | Likely cause | Fix |
|---|---|---|
| Push plate does nothing | Dead actuator battery, wiring fault, or operator in off mode | Test the actuator and circuit, then repair or replace it |
| Door won't stay open long enough | Hold-open time set too short | Re-program the hold-open and speed settings |
| Door closes on people | Presence sensor misaligned or failed | Re-aim or replace the safety sensors and re-test |
| Slide door stalls | Worn rollers, dirty track, or a belt problem | Clean the track and replace rollers or the belt |
| Constant false openings | Motion sensor detecting sidewalk traffic | Narrow the sensor pattern and re-tune |
Most accessible entrances use a low-energy swing operator, activated by a push plate or wave switch, that opens the door slowly enough to be safe without guard rails or presence sensors in many installations. Grocery stores, hospitals, and big-box retail usually use full-power automatic doors, often sliding, that open on approach and depend on sensors for safety. The two are built to different standards, ANSI/BHMA A156.19 and A156.10, and we service both.
We also add operators to existing manual doors. Usually that means checking the door, hinges, and frame first, since an operator can't make up for a sagging door.
The American Association of Automatic Door Manufacturers (AAADM) recommends that owners run a daily safety check and have an AAADM-certified inspector check full-power doors at least once a year.
Tell us the address, which door, and what it's doing. A photo texted after the call helps us bring the right parts.
A technician checks the whole opening: door, frame, hinges or pivots, closer, latch, and threshold. The symptom isn't always where the problem is.
You get a clear repair or replacement price before work starts. If a part has to be ordered, we make the door safe and secure first.
We repair, adjust, and cycle the door until it closes, latches, and locks on its own every time, then walk you through what we did.
Medical offices and clinics around University City and the hospital campuses, grocery and retail centers along Independence Boulevard and in Steele Creek, and lobby entrances in Uptown and SouthPark all depend on automatic doors and push-plate operators. When one of those stops working, people who use wheelchairs, walkers, or strollers can't get in.
Charlotte's humidity and summer storms are hard on push-plate wiring and exterior sensors, and spring pollen collects in sliding door tracks. Seasonal cleaning and checks prevent many breakdowns.
Not sure? Call (984) 265-7937. We'll tell you honestly which one your door needs.
Usually, yes. We check the door, frame, and hinges first, then install a low-energy operator with push plates inside and outside.
The motion sensor's detection pattern is too wide or aimed at the sidewalk. We narrow and re-aim it so it only triggers on approach.
AAADM recommends a daily owner safety check and an annual inspection by an AAADM-certified inspector for full-power doors.
No. Only within Charlotte city limits.
Aluminum and glass entrances: pivots, floor and overhead concealed closers, narrow-stile locks, and alignment.
View service →Slamming, leaking, or weak closers adjusted or replaced, with ADA closing speed and opening force set correctly.
View service →New and replacement doors, frames, and hardware for storefronts, offices, warehouses, and fire-rated openings.
View service →Planned visits that inspect, adjust, and lubricate every door so problems are caught before they become emergencies.
View service →Charlotte businesses only. No forms, no waiting for a callback. Talk to us now.