Automatic & ADA Door Repair
Automatic swing and slide doors, push-plate operators, and sensors repaired, adjusted, and safety-checked.
View service →Your storefront door is the first thing customers touch. We repair aluminum and glass entrances across Charlotte, including sagging doors, worn pivots, leaking floor closers, failed concealed closers, and narrow-stile locks that won't throw.
| Door types | Narrow, medium, and wide stile aluminum; all-glass entrances |
|---|---|
| Hanging | Offset pivots, center-hung pivots, butt hinges, continuous hinges |
| Closers | Floor closers, overhead concealed closers, surface closers |
| Locks | Narrow-stile deadlocks, hook bolts, rim exit devices, flush bolts |
| Where | Charlotte city limits only |

What we usually find when a Charlotte business calls about this, and what we do about it.
| Symptom | Likely cause | Fix |
|---|---|---|
| Door drags at the latch side | Worn top or intermediate pivot, or stripped pivot screws in the stile | Replace the pivots and reinforce the stile fasteners |
| Door won't stop at closed | Floor closer has lost its hydraulic fluid | Replace the floor closer and reset the spindle |
| Door slams or drifts open | Concealed closer valves out of adjustment or the closer has failed | Re-tune the valves or replace the concealed closer and arm |
| Deadlock won't throw | Door has dropped and the bolt hits the strike | Re-align the door, then service the lock and cylinder |
| Pairs won't meet in the middle | Pivots worn unevenly on a pair of doors | Re-hang both leaves and re-set the meeting stiles |
Most Charlotte storefronts use aluminum stile-and-rail doors hung on offset pivots or a continuous hinge, and closed by a closer hidden in the floor or in the header above the door. Because that hardware is concealed, problems show up as symptoms: the door drags, swings past closed, or won't latch. We open up the floor closer pit or the header, find the worn part, and replace it with hardware that fits your door's preps.
Narrow-stile doors also use specialized locks. The deadlock, cylinder, and thumbturn have to line up within a few millimeters. When a door drops even slightly, the lock is usually the first thing to stop working. That's why we re-align the door before replacing the lock.
Storefront entrances also need to seal and look right. We replace worn door sweeps, pile weatherstripping, and threshold seals, and we can replace damaged door lites and tempered glass panels. If the door has been damaged in a break-in, see our emergency door repair page for how we secure the opening first.
Tell us the address, which door, and what it's doing. A photo texted after the call helps us bring the right parts.
A technician checks the whole opening: door, frame, hinges or pivots, closer, latch, and threshold. The symptom isn't always where the problem is.
You get a clear repair or replacement price before work starts. If a part has to be ordered, we make the door safe and secure first.
We repair, adjust, and cycle the door until it closes, latches, and locks on its own every time, then walk you through what we did.
Charlotte storefronts take a beating. Restaurant entries in South End and Plaza Midwood see heavy weekend crowds, Uptown lobbies take steady weekday commuter traffic, and retail along Independence Boulevard and in Steele Creek faces long afternoons of direct sun. Dark-anodized aluminum heats up and expands in that sun, and a door with worn pivots that clears in the morning can start rubbing by 4 p.m.
Spring pollen packs into the threshold and floor-closer cover plate. Summer storms push wind against tall glass doors and strain pivots and closer arms. A short seasonal check catches most of this before the door fails. Our scheduled maintenance visits are built for exactly that.
Not sure? Call (984) 265-7937. We'll tell you honestly which one your door needs.
A floor closer that is leaking oil has failed internally and should be replaced. If it's only out of adjustment, we can re-tune the closing and latching speeds.
Usually it's worn pivots or loose pivot fasteners letting the door drop. We check the pivots, the closer spindle, and the threshold before replacing anything.
Yes. We replace narrow-stile deadlocks, cylinders, thumbturns, and rim exit devices, and we re-align the door so the new lock throws smoothly.
No. We work only within Charlotte city limits.
Automatic swing and slide doors, push-plate operators, and sensors repaired, adjusted, and safety-checked.
View service →Slamming, leaking, or weak closers adjusted or replaced, with ADA closing speed and opening force set correctly.
View service →Doors that won't lock, won't close, or were damaged in a break-in or storm, secured fast and repaired properly.
View service →Doors that drag, sag, won't latch, or won't lock – diagnosed and fixed on the first visit whenever parts allow.
View service →Charlotte businesses only. No forms, no waiting for a callback. Talk to us now.