Commercial Door Repair
Doors that drag, sag, won't latch, or won't lock – diagnosed and fixed on the first visit whenever parts allow.
View service →A door closer controls how your door opens, closes, and latches. When it slams, drifts, leaks oil, or won't pull the door shut, we adjust or replace it and set it correctly for your opening, including ADA closing speed and opening force.
| Closer types | Surface (regular, parallel, top jamb), concealed overhead, floor |
|---|---|
| Common causes | Seal failure, wrong spring size, valve drift, wind damage |
| Settings we tune | Sweep speed, latch speed, backcheck, delayed action |
| Code targets | ADA closing time and opening force where required |
| Where | Charlotte city limits only |

What we usually find when a Charlotte business calls about this, and what we do about it.
| Symptom | Likely cause | Fix |
|---|---|---|
| Oil leaking from the body | Internal seals have failed | Replace the closer. Leaking closers can't be reliably refilled. |
| Door slams | Sweep or latch valve open too far, or the closer has lost fluid | Adjust the valves, or replace the closer if it's leaking |
| Door won't latch | Latch speed too slow, or spring power too low for the door | Adjust latch speed or install a correctly sized closer |
| Door hard to open | Spring power set too high for an interior door | Reduce spring power to meet opening-force limits |
| Arm bent or torn off | Wind or abuse past the backcheck | Replace the arm and add a stop or a heavier-duty arm |
Most closers have separate valves for sweep speed (the main swing), latch speed (the last few inches), and backcheck (cushioning when the door is thrown open). Many problems are fixed by setting those valves correctly. If the closer is leaking oil, though, the internal seals have failed and the closer needs to be replaced. Turning the valves won't bring it back.
Spring size matters too. A closer that's too weak won't overcome Charlotte's afternoon wind or the stack pressure in a tall building, and one that's too strong makes an interior door hard to open. We match the closer to the door's width, weight, location, and traffic.
Where the 2010 ADA Standards apply, the closer has to give people enough time and enough ease to get through the door:
We set and test these on site. If your door needs to be fully hands-free, see automatic & ADA door repair.
Tell us the address, which door, and what it's doing. A photo texted after the call helps us bring the right parts.
A technician checks the whole opening: door, frame, hinges or pivots, closer, latch, and threshold. The symptom isn't always where the problem is.
You get a clear repair or replacement price before work starts. If a part has to be ordered, we make the door safe and secure first.
We repair, adjust, and cycle the door until it closes, latches, and locks on its own every time, then walk you through what we did.
Exterior doors in Charlotte deal with summer thunderstorm gusts that catch a door and throw it past its stop. That bends closer arms and pulls screws out of the header. Glass lobby doors in Uptown and SouthPark towers also fight stack pressure in the building, which can keep a door from latching unless the closer is sized and tuned for it.
Inside, office suites in Ballantyne and medical offices around University City often have interior doors set far too heavy. That's a common accessibility complaint and is easy to fix with the right adjustment or closer.
Not sure? Call (984) 265-7937. We'll tell you honestly which one your door needs.
No. Oil leaking from a closer means its internal seals have failed. It needs to be replaced to control the door safely.
Under the 2010 ADA Standards, a door with a closer should take at least 5 seconds to move from 90 degrees open to 12 degrees from the latch.
The latch speed is usually set too slow, or the closer's spring power is too low for the door, wind, or building pressure. Both are fixable.
Yes. We service surface, concealed overhead, and floor closers on Charlotte storefronts and interior doors.
Doors that drag, sag, won't latch, or won't lock – diagnosed and fixed on the first visit whenever parts allow.
View service →Aluminum and glass entrances: pivots, floor and overhead concealed closers, narrow-stile locks, and alignment.
View service →Automatic swing and slide doors, push-plate operators, and sensors repaired, adjusted, and safety-checked.
View service →Annual NFPA 80 fire door inspections with written reports, plus repairs to close out deficiencies.
View service →Charlotte businesses only. No forms, no waiting for a callback. Talk to us now.